Gamma Progression II Floor Stand Bedienungsanleitung PDF herunterladen

Base Assembly

Remove the Lower Support Column from the carton. Align the holes in the Base Leg with the

matching holes in the Lower Support Column Post Plate. Loosely secure the Base Leg with one

button head cap screw, inserted through the Lower Support Column Post Plate, the hole in the leg

and threaded into the Bottom Plate. Repeat this procedure for the three remaining Base Legs.

Once all Base Legs are in place, securely tighten the cap screws. Place one lock washer and one

locking nut on each screw, where it protrudes from the Bottom Plate, and tighten securely with

the 10MM Box Wrench.

Support Column Assembly

Insert the Upper Support Column into the Lower Support Column / Base Leg assembly. Leave the

Upper Column extended about 1/2 of its length and lock in place with the two Column Height Lock

Screws located at the top of the Lower Column Support.

Attachment to Progression II Machine Base

Position the Progression II machine over the Flange Plate and align the four holes located in the center

of the machine base with the four center “P” holes of the flange plate. Secure the base of the machine

to the flange plate using the four feet from the machine base.

Attachment to X-Stringer X-Es and X-ST Machine Base

Position the X-Es or X-ST machine over the Flange Plate and align the attachment holes located in

the two slide brackets near the center of the machine base with the two “XA” holes of the flange

plate. Secure the base of the machine to the flange plate using two of the feet from the machine

base.

Attachment to X-Stringer X-6FC, X-6 and X-2 Machine Base

Remove the four feet from the base of the machine and loosen the set screws in the four slide

brackets located in the corners. Reposition the slide brackets to align the feet attachment holes with

the four corner “XB” holes located in the flange plate of the floor stand with the machine base

centered on the flange plate. Tighten the set screws in the slide brackets and secure the base of

the machine to the flange plate using the four feet.

Base Foot Height Adjustment

Each foot of the Floor Stand can be adjusted to level the stand on uneven surfaces. Remove the

Endcap from the leg to be adjusted, loosen the Base Foot Nut located inside of the leg tube with

the 10MM wrench. Adjust the foot to the desired level by turning the hex nut located between the

Base Foot and the the Leg Tube. Tighten the hex nut inside the leg tube to lock the foot in place.

Replace the Endcap.

LIMITED WARRANTY

GAMMA SPORTS ("GAMMA") warrants to the original purchaser that the GAMMA Progression Floor Stand ("EQUIPMENT")

purchased is free from defects in materials and workmanship for a period of five (5) years from the date of original purchase. Should any

defects develop under normal use within the specified time periods, GAMMA will at its option, repair or replace the defective

EQUIPMENT provided it is returned to GAMMA prepaid at the purchaser's expense. This warranty does not apply to any damage or

defect caused by negligence, abuse, misuse, unauthorized alteration, shipping, handling, or wear and tear as a result of normal use.

GAMMA's obligation under this warranty is limited to repair or replacement of defective EQUIPMENT, and no one is authorized to

promise any other liability. GAMMA shall in no event be liable for any incidental or consequential damages.

To return defective EQUIPMENT, a return authorization (RA#) must be obtained from a GAMMA customer service representative by

calling 1-800-333-0337. The RA# must be marked on the outside of the shipping carton being returned. All returns must be shipped

prepaid by the customer to GAMMA. Please retain the original shipping carton and packing materials for any future shipments.

MPXFS Manual Issue 1 - 051804

GAMMA Progression II / X-Stringer Floor Stand Assembly Instructions

Upper Support Column

Flange Plate

Upper Support Column

Column Height Lock

Screws

Lower Support Column

Leg Tube

Bottom Plate

Base Foot Nut

Lock Nut

Base Foot

"XA"

"P"

"XB"

End Cap

LIMITED WARRANTY 1

Inhaltsverzeichnis

Seite 1 - LIMITED WARRANTY

Base AssemblyRemove the Lower Support Column from the carton. Align the holes in the Base Leg with thematching holes in the Lower Support Column Post

Verwandte Modelle: X-Stringer Floor Stand

Kommentare zu diesen Handbüchern

Keine Kommentare

Gamma Progression II Floor Stand Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sport und Erholung Gamma Progression II Floor Stand herunter. GAMMA Progression II Floor Stand User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: X-Stringer Floor Stand

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sport und Erholung Gamma Progression II Floor Stand